Why the FPC can not use HASL surface treatment?

The hot air solder leveling is a technology developed for the coating of lead-tin on rigid printed circuit boards. Due to the simplicity of this technology, it is also applied to flexible printed board FPC. But we usually don’t suggest to use HASL and suggest to use ENIG.

In modern market, there are no FPC manufacturer will be use HASL surface to instead of ENIG. Although ENIG will be expensive than HASL. Attached the ENIG FPC and HASL FR4 PCB pictures for your reference, please kindly check it.

ENIG
HASL

The hot air leveling is to immerse the board directly in the molten lead-slot, and the excess solder is blown off by hot air. This condition is very demanding for the flexible printed board FPC. If the flexible printed board FPC cannot be immersed in the solder without any measures, the flexible printed board FPC must be clamped to the middle of the screen made of titanium steel. Then, it is immersed in the molten solder. Of course, the surface of the flexible printed board FPC is also cleaned and coated with flux.

Due to the harsh hot air leveling process conditions, it is easy for the solder to be drilled from the end of the cover layer to the underside of the cover layer, especially when the bond strength between the cover layer and the copper foil surface is low, and this phenomenon is more likely to occur frequently. Since the polyimide film is easy to absorb moisture, when the hot air leveling process is used, the moisture absorbing moisture will cause foaming or even peeling of the cover layer due to rapid heat evaporation, so it is necessary to dry and prevent moisture before the FPC hot air leveling management.

As we all know, the Gold is a better finish for the corrosive environment if it is clean going into the field. HASL will typically use a very corrosive flux to prepare the surface and if this is a lead free HASL or leaded it does not matter, both are susceptible to corrosion.

These must be very clean going into the fielded environment or just the residue from the HASL process can set up corrosion cells. The plating process for the gold finish is not as difficult to clean and the residues are typically very low even with RO water rinsing.

If you would like to learn more details or you have any different opinions, please feel free to contact us and let us know at sales@bestfpc.com

You may also like

What should be paid attention to in the bending process of FPC?

Flexibility is the most obvious advantage for flex PCB, but we should maintain a degree during use, not just bend casually, so what should we pay attention to when bending?

BESTFPC1
bestfpc2
  1. Although the FPC can be bent, if it is bent at 180┬░, this may cause damage to the copper traces, and it lead to open or short circuits.
  • Most of the ink-type protective layer is not resistant to bend, such as text/silk screen, marking, solder mask, etc. It is strictly prohibited to have more than 90┬░ bending action in the assembly process.
  • The corners of the FPC outline, which are prone to tearing during the assembly process, reminding users to pay attention to it.
  • The exposed part of the FPC is subjected to surface plating treatment, such as gold/gold plating, etc., the focus is on preventing oxidation. This area is not suitable for bending.
  • Although there is a stiffener design in the golden finger plug-in area, it is still not suitable for bending in this area. Special attention should be paid to the assembly process.
  • Do not bend directly on the via area of FPC.

If you have any design question about bending area, please feel free to contact us at sales@bestfpc.com. We will share more details about increasing the bending times soon.

You may also like

What is the difference between solder mask and coverlay´╝č

Have you ever been have trouble in selecting the solder mask and coverlay when you are design a flex pcb? Solder mask and coverlay has the same basic function of insulating, do you know the difference between solder mask and coverlay? Is it possible to make the solder mask and coverlay overlap together for insulating? Do you think the flexible solder mask is the same as rigid printed circuit solder mask?

1)Design: Actually, coverlay is widely used for flexible printed circuit board. Because of most of flex pcb will need to add the PI/FR4 stiffener and EMI shield. But if there are BGA pads and dense solder mask opening area, limits the minimum size of openings and the minimum web of material then can be retained between adjacent openings. I would like to share a coverlay and solder mask overlap together FPCB with you. The coverlay is applied first and the solder mask second with a slight overlap onto the coverlay to prevent any gaps in the combined layer. This kind of design have much higher requirements for our production to ensure your functional and reliable design. Below picture is a coverlay and solder mask overlay together FPCB, hope you will be interested in.

If the coverlay opening is square, the minimum size for coverlay is 0.6mm, and space is 0.25mm. Otherwise you need to print solder mask. If the coverlay opening is round, the mimimum size for coverlay is 0.25mm, and space is 0.15mm. Otherwise you need to print solder mask. Because too small coverlay webs will be easily damaged or broken during manufacturing process, and the limited of adhesive may not allowed for a good lamination.  Coverlay openings may also exhibit a small amount of adhesive squeeze out into the openings. Then the resulting design rules for coverlay are significantly different than those for solder mask. Attached the coverlay square and round opening picture for your reference, please kindly check it.

2)Thickness: Below is the pure green solder mask flexi pcb picture, it do not need to add the stiffener for PCBA (SMT assembly), and there are no BGA area, why it choose to use the green solder mask instead of coverlay? The normal coverlay thickness is 27.5~50um. And the solder mask thickness is 8~12um. Due to the customers need the ultra thin flex pcb. Then we suggest the customer to use the solder mask instead of the coverlay.

3)Color: The most popular coverlay color is yellow, we usually prepared the yellow, white, black coverlay in stock. Solder mask is available in a wider range of colors: green, black, white, yellow, etc. Please kindly note that the flex pcb solder mask is quite different to rigid pcb. The flex pcb solder mask cost is much higher than FR4 PCB.Because the flexible circuit board solder mask the withstand bending and high temperature is better than Rigid FR4 PCB. But the coverlay and solder mask for flex price is the same for us.

If you have any comments, warmly welcome you to contact us. Once we received your news, we will reply to you immediately. Looking forward to receiving your inquiry.

You may also like